Fórum - Zobrazit téma - Clasp Spring of Washer Motor - www.WMHelp.cz
forum.WMHelp.cz
O všem, co souvisí s Windows Mobile
 
 FAQFAQ   HledatHledat   Seznam uživatelůSeznam uživatelů   Uživatelské skupinyUživatelské skupiny  RegistraceRegistrace 
 Osobní nastaveníOsobní nastavení   Přihlásit se pro kontrolu soukromých zprávPřihlásit se pro kontrolu soukromých zpráv   PřihlášeníPřihlášení 

Clasp Spring of Washer Motor

 
Přidat nové téma   Zaslat odpověď    Obsah fóra WMHelp.cz -> Palm
Zobrazit předchozí téma :: Zobrazit následující téma  
Autor Zpráva
nanyangddmotor
nováček
nováček


Registrace: 3.4. 2020
Příspěvky: 1

PříspěvekZaslal: pá 03. duben, 2020 11:57    Předmět: Clasp Spring of Washer Motor Citovat

The most common problem of Washer Motor is the clasp spring.

During normal washing, the spring should be disengaged. Only when dehydrating, the spring will hold the inner and outer shafts. Since it is not detached from the rust for a long time, or the fixed end of the circlip can not be fixed, the problem can be solved by simply removing the cleaning and lubricating oil, and the pawl wheel is not disengaged when washing, and the location needs to be adjusted.

In addition, please don't ignore: the possibility that the washer motor will rotate but not wash when washing: pulsator card; remove foreign matter; loose pulsator or eclipse at the joint; replace or repair the pulsator. This should be the capacity reduction of the motor capacitor or The belt on the motor wheel is slack and slipped. You can try a capacitor with the same capacity and withstand voltage, and then check if the belt is loose. Use a multimeter to easily determine if the capacitor has a serious breakdown fault. If the resistance is extremely large, it indicates that the resistance is not broken down, but it does not indicate that the capacity is normal.

Assume that the washer motor and capacitor are good. Check the results, there is no problem with the power supply. You can turn the motor first and then energize it immediately.

2 possibilities are as below:

1 winding burning (turn-to-turn short circuit) makes the starting torque sufficient;

2 The capacitor is enough to start the torque. The capacitor has the original rated capacitance and can be started smoothly without adding a new load. (Using a long-oil smoked blade, it is basically sure that the winding short-circuit plus capacitor makes the phase angle deviation 90 degrees, which is good for In the motor winding motor winding group, the short-rotation torque balance causes the motor to be difficult to open. The motor-turning force of the hand-cranked motor is shorter than the same, resulting in the motor balance caused by the stress balance of the motor per pole. The motor is disassembled and the bearing cover is smelled. Paste the taste, sure the motor winding problem is to be repaired.

More information about NanYang Motor please click Washer Motors article source: https://www.zjnanyangmotor.com/news/clasp-spring-of-washer-motor.html
Návrat nahoru
Zobrazit informace o uživateli Odeslat soukromou zprávu
Zobrazit příspěvky z předchozích:   
Přidat nové téma   Zaslat odpověď    Obsah fóra WMHelp.cz -> Palm Časy uváděny v GMT + 1 hodina
Strana 1 z 1

 
Přejít na:  
Nemůžete odesílat nové téma do tohoto fóra.
Nemůžete odpovídat na témata v tomto fóru.
Nemůžete upravovat své příspěvky v tomto fóru.
Nemůžete mazat své příspěvky v tomto fóru.
Nemůžete hlasovat v tomto fóru.


Powered by phpBB © 2001, 2005 phpBB Group

Reklama / Ceník
Vstup pro inzerenty




Webmaster | Hledání | Statistiky | Syndikační kanály WMHelp.cz, informace ze světa Windows Mobile, asistenční služby. ISSN 1802-5684
RSS News | RSS Downloads | Atom News | Atom Downloads | Plucker Text | Plucker Color | Plucker Gray | PDA verze | Právní ujednání | Ochrana osobních údajů